Rosewill Computer Hardware RC 702 User Guide

7.1 Channel PCI Sound Card RC-702  
User Manual  
 
7.1 Channel PCI Sound Card RC-702  
User Manual  
Hardware & Software Installation  
It is recommended that you remove any previously installed sound card and drivers prior to  
installing this 7.1 Channel PCI Sound Card to avoid any conflicts. If previously installed drivers are  
not removed, this 7.1 Channel PCI Sound Card perhaps not function properly. (Note: If your  
computer has on-board sound you will need to disable it on the motherboard. For more  
information please see your computer’s documentation or contact your computer’s manufacturer.)  
Driver Installation  
For Windows® 2000, XP/2003/Vista/7 (32/64 bit)  
1.  
2.  
Locate an available PCI slot on your computer, and insert this 7.1 Channel PCI Sound Card  
into the slot. Fasten the card to the case using a screw.  
Start your PC. Windows® will detect the Sound Card find a “Multimedia Audio Controller”  
device. Click the “Cancel” button to cancel the driver installation for the device at this  
moment. The driver for this device will be installed in the next step.  
Place the Driver CD into the CD-ROM drive. Click the Start button on the taskbar and click  
Run. Type “D:\RC-702\Setup.exe”. (Assuming you have placed the CD in  
CD-ROM drive labeled as D).  
3.  
4.  
5.  
6.  
Follow any on-screen instructions to complete the software installation.  
Restart your system.  
Once you have rebooted the computer, this 7.1 Channel PCI Sound Card is ready to be  
used.  
 
2
7.1 Channel PCI Sound Card RC-702  
User Manual  
Physical Connections  
The rear panel of this 7.1 Channel PCI Sound Card has the following jacks:  
1.  
Line In (blue) – Connect to tape/CD/DVD player, or other audio sources for output mixing  
and/or recording  
2.  
3.  
Mic In (pink) – Connect to microphone  
Front Out (green) - This jack should connect to the powered Left and Right speakers,  
located to the left and right of your computer monitor. If you have just a two-speaker  
stereo setup, this is the jack to use. You can also plug a pair of stereo headphones into  
this jack  
4.  
5.  
6.  
7.  
Rear Out (black) -This line-level output should be connected to powered Left and Right  
Surround speakers. These speakers should be located to your left and right sides, just  
behind your head  
Surround Out (black) -The line-level output connects to powered Left and Right Center  
Surround channel speakers. These speakers should be located directly you as you are  
looking at your computer monitor  
Center/Subwoofer (orange) -This line-level output connects to powered Center and  
Subwoofer speakers. The Center channel speaker should be directly above or below your  
monitor and the subwoofer can go just about anywhere it will fit in your room.  
S/PDIF Out -The Digital Output jack is a S/PDIF Coaxial output  
you can use an RCA cable to connect this to a digital recorder, mixer or surround receiver.  
A 75 Ohm digital coaxial cable is required for this type of connection  
 
3
7.1 Channel PCI Sound Card RC-702  
User Manual  
In addition to the rear panel jacks, this 7.1 Channel PCI Sound Card also has the following internal  
connection:  
The Connector  
The Function  
J6  
J3  
Aux-in  
Analog CD/IN Port(Signals: L-G-G-R)  
 
4
J4  
J7  
Analog CD/IN Port(Signals: G-R-G-L)  
PCSPK-in  
J11  
JP1  
CD-SPDIF IN  
OPTICAL SPDIF- I/O  
Thank you for purchasing a quality Rosewill Product.  
product.  
5
 

QSC Audio Speaker System MD FP122 124r User Guide
Quatech Switch QSCLP 100 User Guide
Reebok Fitness Treadmill RBTL22920 User Guide
Renesas Computer Hardware H8S 2169 Series User Guide
Rheem Water Heater RTG2 42PV User Guide
Roberts Radio Portable Radio Classic DAB User Guide
Samsung Cell Phone GH68 06114A User Guide
Samsung Printer CLX 3170FN User Guide
Samsung Vacuum Cleaner DJ68 00368Q User Guide
Sapphire Audio Computer Hardware ML00042 R5 User Guide