Rosewill Network Card RC210 User Guide

E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
 
E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
Mobile DVD and Mobile CD-RW.  
1.2. Package Contents  
• Low Profile Serial ATA 2 Channel PCI Host Adapter  
• This Users Manual  
• Driver CD  
• Low Profile Size PCI Bracket ( Not supported on Model D)  
2. Software Installation  
This section provides the information on how to install the drivers of Low Profile Serial ATA 2 Port  
PCI Host Adapter for the operating systems:  
New & Existing Windows 98/98 SE  
New & Existing Windows ME  
New & Existing Windows NT 4.0  
New & Existing Windows 2000  
New & Existing Windows XP  
2.1. Windows 98/98SE Driver Installation  
For New Windows 98/98 SE Systems  
1. After the SATA PCI Host Adapter and attached drives are configured, follow Microsoft  
procedures to install Windows accordingly.  
2. Once Windows has been installed, double click My Computer/Control Panel/System, then click  
Device Manager.  
3. Double click Other Devices then PCI RAID Controller.  
4. Click Driver tab, then Update Driver.  
5. Insert the Driver diskette and click Next.  
6. Select Search for a better driver than the one ...option and click Next.  
7. Check Specify a location, uncheck the other boxes, type in E:\ (If your CD-ROM/DVD is E:\)  
and click Browse.  
8. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click OK and then Next.  
9. Click Next and then Finish.  
10.Remove the Driver CD and click Yes to restart Windows to complete driver installation.  
2
 
E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
For Existing Windows 98/98 SE Systems  
1. After the Serial ATA PCI Host Adapter and attached drives are configured, boot up Windows.  
2. At the Add New Hardware Wizard, click Next.  
3. Select Search for the best driver for your device option and then click Next.  
4. Insert the Driver CD, check Specify a location, uncheck the other boxes, and click Browse.  
5. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click OK and then Next. (If your CD-ROM/DVD is E:\)  
6. Click Next and then Finish respectively.  
2.2. Windows ME Driver Installation  
For New Windows ME Systems  
1. After the Serial ATA PCI Host Adapter and attached drives are configured, follow Microsoft  
procedures to install Windows accordingly.  
2. Once Windows has been installed, click My Computer, then click Properties. Click Device  
Manager tab.  
3. Double click Other Devices then PCI RAID Controller.  
4. Click Driver tab, then Update Driver.  
5. Insert the Driver CD, check Specify the location of the driver (Advanced) and click Next.  
6. Select Search for the better driver option, check Specify a location, uncheck Removable  
Media, type in E:\ (If your CD-ROM/DVD is E:\), and click Browse.  
7. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click OK and then Next.  
8. Click Next and then Finish.  
9. Remove the Driver diskette and click Yes to restart Windows to complete driver installation.  
For Existing Windows ME Systems  
1. After the Serial ATA PCI Host Adapter and attached drives are configured, boot up Windows.  
2. At the Add New Hardware Wizard, check Specify the location of the driver (advanced), and  
click Next.  
3. Insert the Driver CD, check Specify a location, uncheck the other boxes, and click Browse.  
4. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click OK and then Next.(If your CD-ROM/DVD is E:\)  
5. Click Next and then Finish.  
Verification of the Proper Installation for Windows 98/98SE/ME  
1. Double click My Computer/Control Panel/System. Click Device Manager tab.  
2. Double click SCSI Controllers, Silicon Image Sil-3x12 SATA Raid Controller should be listed.  
3. Highlight Silicon Image Sil-3x12 SATALink Controller and click Properties. A message This  
3
 
E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
device is working properly is displayed in the dialog box, the driver has been correctly  
installed. If any error message is displayed, remove Silicon Image Sil-3x12 SATALink Controller  
and restart your system.  
2.3. Windows NT 4.0 Driver Installation  
For New Windows NT 4.0 System  
1. Before installation, copy all the files under directory E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_  
me _2000_xp_nt4.0\ driver\ *.* to a blank floppy disk.  
2. After the SATA PCI Host Adapter and attached drives are configured, follow Microsoft  
procedures to install Windows accordingly.  
3. At the Windows Set-up screen, press F6 to specify and add the driver.  
4. Press S, select Other, then press Enter.  
5. Insert the Driver diskette and press Enter.  
6. Select Silicon Image Sil-3x12 SATALink Controller Driver and press Enter.  
7. Press Enter to continue and follow on-screen instructions to complete Windows NT 4.0  
installation.  
Add Windows NT 4.0 Driver on Original Booting Device  
1. After the SATA PCI Host Adapter and attached drives are configured, boot up Windows.  
Double click My Computer/Control Panel/SCSI Adapters, then click the Drivers tab.  
2. Click Add… then Have Disk....  
3. Insert the Driver CD in your CD-ROM/DVD drive and type in E:\ (If your CD-ROM/DVD is E:\),  
then click Browse.  
4. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click Open then OK.  
5. Highlight Silicon Image Sil-3x12 SATALink Controller and click OK.  
Verification of the Proper Installation for Windows NT 4.0  
1. Double click My Computer/Control Panel/SCSI Adapters.  
2. Highlight Silicon Image Sil-3x12 SATALink Controller and click Properties. This device is  
working properly is displayed in the dialog box, the driver has been correctly installed.  
2.4. Windows 2000 Driver Installation  
For New Windows 2000 Systems  
1. Before installation, copy all the files under directory E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_  
me _2000_xp_nt4.0\driver\ *.* to a blank floppy disk.  
2. After the SATA PCI Host Adapter and attached drives are configured, follow Microsoft  
procedures to install Windows accordingly.  
3. At the Windows Set-up screen, press F6 to specify and add the driver.  
4. Insert the Driver diskette. Press S, then press Enter.  
4
 
E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
5. Select Silicon Image Sil-3x12 SATALink Controller Driver and press Enter.  
6. Press Enter to continue and follow on-screen instructions to complete installation.  
Add Windows 2000 Driver on Original Booting Device  
1. After the SATA PCI Host Adapter and attached drives are configured, boot up Windows.  
2. At the Found New Hardware Wizard, click Next.  
3. Select Search for a suitable driver for my device (recommended) and click Next.  
4. Insert the Driver CD in your CD-ROM/DVD drive, check Specify a location, uncheck the other  
boxes, click Next, type in E:\ (If your CD-ROM/DVD is E:\). Click Browse.  
5. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click Open then OK.  
6. If the Digital Signature Not Found message appears, click Yes. (Note If prompted for Windows  
2000 CD-ROM, insert the CD and click OK. Type in E:\I386, click OK and Finish.  
(assuming E: is your CD-ROM drive))  
7. Click Finish.  
2.5. Windows XP Driver Installation  
For New Windows XP Systems  
1. Before installation, copy all the files under directory E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_  
me _2000_xp_nt4.0\driver\ *.* to a blank floppy disk.  
2. After the SATA PCI Host Adapter and attached drives are configured, follow Microsoft  
procedures to install Windows accordingly.  
3. At the Windows Set-up screen, press F6 in order to specify and add the driver.  
4. Insert the Driver diskette. Press S then press Enter.  
5. Select Silicon Image Sil-3x12 SATALink Controller Driver and press Enter.  
6. Press Enter to continue and follow on-screen instructions to complete Windows XP installation.  
Note: When the Software Installation warning pops up, click Yes. And when the Hardware  
Installation warning pops up, click Yes again.  
Add Windows XP Driver on Original Booting Device  
1. After the SATA PCI Host Adapter and attached drives are configured, boot up Windows.  
2. At the Found New Hardware Wizard, check Install from a list or specific location (advanced),  
then click Next.  
3. Insert the Driver CD. Check Include this location in the search, uncheck the other box, type in  
E:\, and click Browse.  
4. Points specify a location, example E:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_  
nt4.0 \ Driver, click OK then Next.  
5. When a warning message pops up, click Continue Anyway, then click Finish.  
5
 
E-SATA 1.5G 1+1 Port PCI Adaptor RC210  
User Manual  
Verification of the Proper Installation for Windows 2000/XP  
1. Double click My Computer/Control Panel/System.  
2. Click Hardware then click Device Manager.  
3. Double click SCSI and RAID Controllers, then double click Silicon Image Sil-3x12 SATALink  
Controller to display driver properties.  
4. A message This device is working properly is displayed in the dialog box, the driver has been  
correctly installed.  
Thank you for purchasing a quality Rosewill Product.  
for your product.  
6
 

Renesas Network Card M37641T2 RPD E User Guide
Roberts Gorden Patio Heater 150 User Guide
Roland Stereo Amplifier CUBE 60 User Guide
Rolls Car Amplifier RA170 User Guide
Runco CRT Television DTV 1200 User Guide
Samsung Fish Finder SP R4232 User Guide
Samsung Refrigerator 65602 User Guide
SATO Label Maker M 10e User Guide
Schneider Electric Welding System MNA01M001EN User Guide
Sears Garage Door Opener 13953960SRT User Guide