Rosewill Switch RC 405X User Guide

10/100M Fast Ethernet Switch 5/8 port  
RC-405X/RC-406X  
User Manual  
 
10/100M Fast Ethernet Switch 5/8 port RC-405X/RC-406X  
User Manual  
y
y
y
y
y
y
y
y
y
y
Store-and-forward switching improves overall network performance  
Supports full-duplex switching bandwidth modes, allowing data rates of 10, 20 and 100Mbps  
Full-duplex transfer mode / half-duplex adaptive  
Provides packet switching functions between all sixteen 10/100Mbps Ethernet ports  
10/100Mbps auto-sensing and negotiation allows flexibility between network devices  
Wire-speed forwarding: 148,800pps/100Mbps and 14,880pps/10Mbps  
High-performance memory bandwidth and expansion bus  
Supports the spanning tree protocol, eliminating network loops  
Supports broadcast storm control function  
Supports port trucking and load sharing for high-performance servers and inter-switch links. Provides a convenient  
uplink port for cascading hubs  
y
y
Auto-partitioning and data collision control  
Auto-polarity detection  
Specification  
y
y
y
y
Network standards: IEEE 802.3, IEEE 802.3u, IEEE 802.3x  
Interface Media 10Base-T: 3 or 3 more than UTP, 100Base-TX: 5 types of UTP  
Instructions for each panel port: Link / Act (to connect / work), 10/100Mbps (speed), other: Power (Power)  
Environmental standard operating temperature: 0 -40 , Storage temperature: -40 -70 , Operating  
Humidity: 10% -90% RH non-condensing,  
y
y
Storage humidity: 5% -90% RH non-condensing  
Dimensions (mm): 5-port: 91.5(L)*82(W)*27(H) mm  
8-port: 163(L)*95(W)*28(H) mm  
y
Power Supply: 9V 0.5A  
Figures of Product  
Front Panel  
The unit front panel provides a simple interface monitoring the Switch. It includes a power led and 5/8 led indicator for  
each port.  
y Rear Panel  
y Side Panel  
5-port  
2
 
10/100M Fast Ethernet Switch 5/8 port RC-405X/RC-406X  
User Manual  
5-port Switch’s Uplink Port  
An uplink port is simply an Ethernet port where the Receive (Rx) and the Transmit (Tx) signals are swapped by crossing  
the Transmit and Receive twisted-pair wires.  
This will let the Transmit signal (and twisted-pair) on RC-405X correctly connect to the Receive connection on the other  
device and vice-versa, allowing for stacking similar devices, or simply expanding the number of ports.  
NOTE TO USERS OF 10/100 5-PORT SWITCH: If you connect a router or additional switch to the Uplink port, then you  
cannot use the numbered port next to the Uplink port (port 1X on the 5-Port Switch will be inactive). The two ports are  
wired together, so they cannot be used simultaneously.  
y Rear Panel  
8-port  
5/8-Port Switch indicates a DC (9V) inlet, which accepts 100-240V 50-60Hz power adapter.  
Mounting 8 Port Switch On A Wall  
The 8-port 10/100Mbps Switch can also be mounted on a wall. Four mounting slots are provided on the bottom of the  
switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the  
illustration below:  
1. Mounting on a cement wall  
1. Mount the Nylon screw anchors into a cement wall.  
2. Drive the T3x15L screws into the Nylon screw anchors  
3. Hook the mounting holes of the switch back on the screws; you have completed the wall-mount  
2. Mounting on a wood wall  
1. Drive the T3x15L screws into the wood wall.  
2. Hook the mounting holes of the switch back on the screws; you have completed the wall-mount  
3. Note: For the minimum length of the screws  
1. 3/4 inch minimum for wood wall.  
2. 3 inch minimum for cement wall.  
Thank you for purchasing a quality Rosewill Product.  
Rosewill Customer Service: 1-800-575-9885 or at [email protected]  
3
 

Radio Shack Cooktop 15 1937 User Guide
RCA Car Amplifier AMP1450F User Guide
Rival Waffle Iron WC800 WT User Guide
Russound Satellite Radio CAM66X S1 S2 User Guide
Ryobi Outdoor Trimmer P2600 User Guide
Samsung Cell Phone GH68 05247A User Guide
Samsung Indoor Furnishings SI M8V073BB1EU User Guide
Samsung Printer ML 4512ND User Guide
SATO Label Maker M 8400S User Guide
Sears Vacuum Cleaner 11317066 User Guide