SeaLand Vacuum Cleaner VACUUM HOLDING TANK User Guide

VACUUM  
HOLDING TANK  
OWNER’S MANUAL  
WARNING  
!
This manual must be read and under-  
stood before installation, adjustment,  
service, or maintenance is per-  
formed. Modification of this product  
can result in property damage.  
Dometic Corporation • Sanitation Systems  
13128 State Rt 226, PO Box 38  
Big Prairie, OH 44611  
SeaLand Product Customer Service: 1-800-321-9886  
(8:00 a.m. - 5:00 p.m. ET)  
 
IMPORTANT: Before pumping out the VHT, it  
is recommended that the power to the system be  
turned off. Then, flush the toilet. This releases the  
stored vacuum in the tank, thus, allowing the  
dockside pump to empty the waste out more easily.  
If the dockside pump has low suction capability,  
you may need to flush the toilet a second time  
during the pump out.  
PRINCIPLES OF OPERATION  
VacuFlush systems use a small amount of water (one  
pint to one quart) and the vacuum that is generated by  
the vacuum pump to flush. Each toilet must be con-  
nected to a pressurized water system. Fresh water is  
recommended and will result in an odor-free bathroom.  
If seawater is used, the water should be filtered.  
No complicated user instructions are required. Lifting the  
flush lever adds water to the bowl. Pressing the flush  
lever (or pulling the flush lever on a 106 toilet) opens a  
mechanical seal that allows the vacuum force to pull the  
waste from the bowl as clean water rinses the bowl. The  
vacuum moves the waste (at approximately 7 feet [2.1  
m] per second) through a one-inch opening in the toilet  
base. Incoming air fragments the waste as it passes  
through the base opening. This process eliminates the  
need for macerators or mechanical motors in the toilet  
base.  
The Vacuum Relief Valve (VRV) will automatically open  
at 13" of vacuum and is spring loaded to close at 11" of  
vacuum to prevent leaking during normal operation.  
SYSTEM LAYOUT  
The Vacuum Holding Tank (VHT) system can be installed  
on most boats that presently use a portable, manual or  
electric toilet. The following procedure will be helpful:  
1. Review the typical system layout to get a general  
idea of how the system will operate and what discharge  
options will be considered (see Figure 1).  
Next, the waste is transferred into the Vacuum Holding  
Tank (VHT). System vacuum is monitored by a vacuum  
switch that is located on the outside of the VHT. When  
the switch senses a drop in vacuum in the system, it  
automatically signals the pump to energize and bring  
the vacuum back to operating level. This process is nor-  
mally completed in about one minute.  
2. Draw or obtain a layout of the boat which allows the  
location of head compartments, bulkheads, engine space,  
tanks, through-hull fittings, etc. This layout should include  
top views and side views and show relative distances  
and heights with reasonable accuracy.  
3. Use the information in the Component Locating  
Procedure section to help select the best locations for  
your boat layout.  
In a properly operating system, the stored vacuum will  
“leak” down between flushes, causing the vacuum pump  
to run for a short period. The pump should not run more  
than once every three (3) hours after the last flush.  
4. Routing of vacuum hose should be considered when  
selecting a location for the toilet and the (VHT). A  
maximum of 20 feet (6.1 m) of hose can be used be-  
tween the toilet and the VHT.  
An “On-Off” night switch can be installed to silence the  
vacuum pump during sleeping hours. The VacuFlush  
Status Panel, an optional accessory, features an inte-  
gral circuit breaker that provides a convenient night  
switch.  
5. Before starting the actual installation, carefully re-  
view the Key Installation Points.  
Figure 1  
3
 
COMPONENT LOCATING PROCEDURE  
Check  
Component  
Location  
Vacuum Toilet  
Bathroom  
compartment or  
under berth.  
1. Check dimensions of mounting space above and below floor.  
2. Determine best toilet discharge connection: above floor, out rear or below floor.  
3. Allow at least ½-inch (1.3 cm) clearance between toilet rear and wall.  
4. Make sure compartment, shower and vanity doors will clear toilet bowl.  
5. Check location nearest cold water line.  
6. Water line must be at least ½-inch ID and provide a minimum flow of two (2)  
gallons per minute (7.6 liters per minute).  
7. Water valve assembly for 106 toilet can be positioned any distance horizontally from  
the toilet but must be at least 6 in. (15.24 cm) above the top of the toilet bowl rim.  
8. Check clearances to side wall for installation of flush lever cover and back wall  
for best clearance.  
Vacuum Holding  
Tank (VHT)  
Any space that  
permits access to  
remove the entire  
unit.  
1. The vacuum holding tank (VHT) inlet must be located no more than 20 feet (6.1 m)  
from the toilet discharge.  
2. The VHT inlet must not be located more than 3 feet (.9 m) above the outlet of  
the toilet. (NOTE: The lower the tank, the better the system efficiency.)  
3. The VHT must be mounted in a horizontal position.  
4. The VHT must not be exposed to temperatures over 120°F. Do not place near  
heat sources such as engine manifolds, water heaters, generators, etc.  
Mounting space must provide for free air flow.  
Vacuum Hose  
and Fittings  
Use only Odor-  
Safe hose and  
SeaLand fittings.  
They are made to  
fit together.  
1. OdorSafe Sanitation Hose must be used; it is sized to use SeaLand fittings in the  
system, minimizing vacuum leakage.  
2. It is important that restrictions in the vacuum hose be kept to a minimum.  
Where a bend must occur in a hose run, the radius of the bend must not be  
less than 6 inches (15.24 cm). If a tighter radius is required, use a SeaLand 90°  
bend kit to assure a clog-free transition.  
4. Hose…Too Much, Too Little  
KEY INSTALLATION POINTS  
Try to avoid unnecessary hose runs that result in  
excessive bends or loops. Excessive hose reduces  
vacuum transfer efficiency. Hose should be securely tied  
down every three feet. Too little hose length also causes  
problems by forcing the hose into tight bends or kinks.  
Always leave a small amount of extra hose length for  
future maintenance. The distance between the toilet and  
the Vacuum Holding Tank (VHT) may not exceed 20 feet  
(6.1 m).  
The VacuFlush system operates on a unique and un-  
common principle – powerful, instantaneous vacuum  
force. As a result, certain installation points must be  
stressed because they are the most common sources of  
incorrect installation.  
1. Leaks at Fitting Joints  
One benefit of vacuum operation is that leaks are inward  
and will not cause drippage of sewage. Vacuum leaks  
result in frequent cycling of the vacuum pump which  
causes unnecessary wear on the motor and gear drive.  
Most vacuum leaks occur at fitting joints. Care should be  
taken to assemble fitting joints per the instructions.  
Allow time in your installation schedule to give cemented  
fittings, if used, time to cure before manipulating them.  
Also, a proper PVC cleaner or primer must be applied  
prior to cementing fittings.  
5. Hose… Wrong Type  
To complete a VacuFlush installation, OdorSafe Sanita-  
tion Hose or rigid PVC pipe (Schedule 40 or heavier)  
must be used.  
6. Hose… Odor Permeation  
Avoid low spots in hose or sections where waste will  
remain for very long periods. Waste trapped in hose will  
produce gases in the final stage of decomposition that  
are very difficult to contain. If possible, have hose from  
the toilet drain into the VHT.  
2. Cementing Hose to Fittings  
Never cement hose to fittings. The SeaLand custom hose  
adapter is specifically designed to fit precisely into the  
OdorSafe Hose. The hose will slide easily on the fitting if  
it is lubricated with liquid dishwashing detergent and  
twisted clockwise when attached.  
7. Protecting Toilet and Preventing Objects from  
Falling into System During Installation.  
After mounting toilet and attaching seat and lid assem-  
bly, slide seat assembly carton over seat and lid. Next,  
place toilet box down over toilet. This will ensure addi-  
tional protection to the toilet after installation.  
3. Locating Components in Accessible Spaces  
Never locate a component of the vacuum system in a  
space which is inaccessible or difficult to reach.  
Failure to follow recommended procedures that result  
in any of the above problems will invalidate component  
warranty.  
4
 
INSTALLATION OF COMPONENTS  
4. Mounting the Vacuum Holding Tank  
1. Installing the Toilet  
The Vacuum Holding Tank (VHT) can be located in any  
accessible space as long as the 1-1/2 inch hose is not  
longer than 20 feet (6.1 m) and its inlet is not higher than  
3 feet (.9 m) from the toilet outlet. The VHT must be  
mounted horizontally.  
For VacuFlush and EcoVac toilet mounting, follow the  
instructions in the VacuFlush Installation Guide.  
2. Routing and Installing Hose  
Before attaching the vacuum hose to a fitting, place two  
hose clamps over hose end. (All connections must be  
double clamped.) Apply liquid dishwashing soap to out-  
side of hose connector and inside hose. Twist hose  
clockwise as it is pushed onto adapter (see Figure 2).  
Hose end should be flush against the fitting shoulder  
when properly installed (see Figure 3). Twist the hose  
counter-clockwise before placing it onto the fitting. This  
will ease installation. All joints should be double clamped  
with high quality stainless steel clamps. Make sure clamp  
mechanisms are 180° from each other when tight  
(see Figure 3). Failure to follow these procedures will  
result in vacuum leaks.  
Mounting spindles are provided for securing the VHT in  
areas that prevent access to the rear mounting feet on  
the VHT.  
Position the VHT in the space intended. If using mount-  
ing spindles, mark holes at rear of tank. After holes are  
marked, remove VHT and secure (3) of the spindles pro-  
vided to the mounting surface using (3) #12 x 1-1/2 inch  
long pan head wood screws. Slide the VHT back so  
mounting spindles fit into slots on tank (see Figure 4).  
Secure the tank by using the (3) remaining spindles and  
(3) #12 x 1-1/2 inch long pan head wood screws on re-  
maining tank mounts.  
If not using the mounting spindles, secure the VHT with  
(8) #12 x 1-1/2 inch long pan head wood screws and (8)  
flat washers on all (8) tank mounts. NOTE: The VHT must  
be secured by at least (6) of the (8) mounting feet.  
Figure 2  
Once the VHT is in place, connect hose from toilet.  
(NOTE: Hose insert elbow fittings can be removed from  
VHT.)  
5. Making Electrical Connections  
See the “Wiring Diagram” section of this manual.  
6. Completing the Installation  
Figure 3  
Complete installation of discharge hose from outlet of VHT  
to a discharge deck fitting or overboard discharge pump.  
Figure 4  
3. Connecting the Toilet Water Supply Lines  
The water supply inlet must connect to an adapter which  
will adapt to the 1/2-inch MPT connection on the toilet  
water valve. (This adapter can be found through a local  
supplier or through Dometic.) The water supply must  
provide a minimum flow of two (2) gallons per minute  
(7.6 liters per minute).  
5
 
WINTERIZING  
6. Drain potable water tank.  
At the end of each boating season, the VacuFlush system  
must be winterized for storage. The following procedure  
should be used:  
7. Add freshwater antifreeze to potable water tank.  
8. Flush potable water antifreeze and water mixture  
through toilet and into the vacuum holding tank. Each  
installation is different so amounts may vary. User  
discretion is required to assure adequate protection.  
1. Thoroughly flush system with fresh water.  
2. Pump out holding tank.  
3. Shut off water supply to toilet, remove waterline.  
4. Press flush lever until all water is drained from toilet.  
5. Turn off electrical power.  
9. Pump out vacuum holding tank.  
10. Turn off electrical power.  
To use antifreeze, repeat Steps 1 and 2 above and  
continue as follows:  
CAUTION: The use of freshwater antifreeze that  
contains alcohol will result in damage to your sanita-  
tion system. Only use propylene glycol freshwater an-  
tifreeze that does not contain alcohol.  
TROUBLESHOOTING GUIDE  
Possible Cause  
Service Instructions  
Problem  
a. Flush ball in toilet leaks.  
a. Leave small amount of water in toilet. If water is  
sucked from bowl, refer to “Troubleshooting  
Guide” in VacuFlush Owner’s Manual.  
1. Pump running too much  
between flushes.  
b. Vacuum line leak.  
b. Tighten all hose connections at pump, vacuum tank,  
holding tank, and toilet.  
c. Foreign material has fouled  
air pump valves.  
c. Disassemble air pump and inspect under the  
two flat disk valves. If foreign material is  
present, remove debris and reassemble air pump.  
d. Inspect diaphragm in pump for small hole or rip.  
Replace if necessary.  
d. Pump diaphragm worn or  
damaged.  
e. Duckbill valve in discharge  
fitting stuck open.  
e. Disassemble discharge outlet and inspect  
duckbill valve. Clean or repair if necessary.  
2. Toilet will not flush.  
(No vacuum.)  
a. Pump will not run.  
b. Plugged vacuum line.  
a. See problem 3.  
b. Blockage usually at base of toilet below flush  
valve. You may have to disconnect line and clear.  
c. Inspect and clean pump valves. Replace if needed.  
d. Disassemble lines and clean.  
c. Plugged pump valve.  
d. Vacuum pump discharge or  
intake lines plugged.  
3. Pump will not run.  
a. No power.  
b. Loose or broken electrical  
wiring.  
a. Check input power, circuit breaker and fuse.  
b. Tighten or reconnect wires at pump and  
vacuum tank.  
c. Improper electrical  
connections.  
d. Faulty vacuum switch.  
c. Make certain wires at vacuum switch are  
connected to the “B” terminals.  
d. To check vacuum switch, short across “B” terminals  
with jumper wire.  
e. Faulty motor.  
e. Replace motor.  
4. Pump will not shut off.  
a. Insufficient vacuum.  
b. Excessive vacuum leak.  
c. Faulty vacuum switch.  
d. Improper wiring.  
a. Verify pump pulls minimum 10 inches Hg of vacuum.  
b. See problem 1.  
c. To check switch, remove one “B” terminal wire.  
d. Check wiring. Refer to Wiring Diagram.  
5. Pump is making a  
loud noise.  
NOTE: If sound of pump is  
disruptive at night, an “On-Off”  
switch may be easily added to the  
system. The VacuFlush Status  
Panel features an integral circuit  
breaker which also serves as a  
night switch. (#500012, 12 VDC;  
#500024, 24 VDC)  
a. Loose set screw in crank  
assembly.  
b. Pump bearing is worn.  
a. Remove cover from pump and check crank  
assembly setscrew for tightness.  
b. Check pump bearing for wear. Replace if needed.  
c. Disassemble air pump assembly and inspect  
inside of pump body for foreign objects.  
d. Replace motor assembly.  
c. Dirt or debris in pump body.  
d. Worn or defective motor.  
e. Motor loose from mounting  
bracket.  
e. Tighten the two (2) nuts securing the motor to  
the mounting bracket.  
6
 
TROUBLESHOOTING GUIDE  
Possible Cause  
Service Instructions  
Problem  
6. Pump running too slow,  
overheating, blowing  
a. Improper voltage.  
b. Loose or broken electrical  
wiring.  
a. Check input power for low voltage.  
b. Tighten or reconnect wires.  
fuses or circuit breakers.  
c. Improper wire size.  
c. Wire size too small – check  
electrical diagram for proper wire  
size for voltage of pump used.  
d. Check motor and replace if necessary.  
e. Disassemble air pump and empty out water.  
d. Gear motor worn or defective.  
e. Tank is overfilled – air pump  
forced to pump water.  
7. Difficulty in emptying  
waste from holding  
tank.  
a. The dockside pump is very  
weak and has low suction  
capability.  
a. Turn off the power to the VHT system. Flush  
the toilet, releasing all the stored vacuum. Begin  
pumping out. Repeat flushing if the dockside pump  
begins having trouble emptying out the waste.  
8. Pump emits odor.  
9. System emits odor.  
a. Worn, torn, or punctured  
pump diaphragm.  
a. Replace pump diaphragm.  
a. Check for improper flexible  
hose.  
a. Replace hose where necessary. Replacement  
hose should be marked “OdorSafe.”  
Important Owner Information: OdorSafe® Sanitation Hose is formulated for transfer of sanitary waste  
only. Do not allow the following items in system: Strong acids or caustic chemicals (example: drain open-  
ers), petroleum solvents or fuels, alcohol-based products (example: alcohol-based antifreeze), pine oil-  
based products (example: Pinesol® cleaner). Use of products containing these substances will void  
warranty on hose.  
DIMENSIONAL SPECIFICATIONS  
7
 
MANUFACTURER’S ONE-YEAR LIMITED WARRANTY  
Dometic warrants, to the original purchaser only, that this product, if used for personal, family or household purposes, is free from  
defects in material and workmanship for a period of one year from the date of purchase.  
If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to be free of  
defects in material and workmanship for a period of ninety (90) days from the date of purchase.  
Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to be defective in  
material or workmanship. All labor and transportation costs or charges incidental to warranty service are to be borne by the  
purchaser-user.  
EXCLUSIONS  
IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGES RESULT-  
ING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE, ALTERATION OR USE OF  
UNAUTHORIZED COMPONENTS. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT-  
ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE YEAR FROM DATE OF  
PURCHASE.  
IMPLIED WARRANTIES  
No person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.  
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from the date  
of purchase for products used for personal, family or household purposes, and ninety (90) days from the date of purchase for  
products placed in commercial or business use.  
OTHER RIGHTS  
Some states do not allow limitations on the duration of an implied warranty and some states do not allow exclusions or limitations  
regarding incidental or consequential damages; so, the above limitations may not apply to you. This warranty gives you specific  
legal rights, and you may have other rights which may vary from state to state.  
To obtain warranty service, first contact your local dealer from whom you purchased this product.  
Dometic Corporation • Sanitation Systems  
13128 State Rt 226, PO Box 38  
Big Prairie, OH 44611  
SeaLand Product Customer Service: 1-800-321-9886  
(8:00 a.m. - 5:00 p.m. ET)  
® Registered; ™ Trademark of Dometic Corporation  
® Uniseal is a registered trademark of Injection Plastics, Inc.  
© 2002 Dometic Corporation  
600343026 10/03  
 

Radio Shack Network Card 624VDC User Guide
RCA VCR VR708HF User Guide
Ricoh Network Card AR B1045 User Guide
Ricoh Photo Printer MP C4000 User Guide
Ryobi Router R160 User Guide
Samsung Microwave Oven ME1040WA BA SA GA User Guide
Samsung Speaker System MXFS9000ZA User Guide
Sanyo Battery Charger HR 4 5FAUP User Guide
Sanyo DVD Player DVD DX517 User Guide
Sears Refrigerator 245 User Guide